Climate conditioning

RP Thermometer / Hygrometer LCD @

Range from 10°C to 50°C (14°F to 122°F) and 20% to 90% humidity Note: Do not place in the direct surroundings from heat and humidification sources

RP Thermometer / Hygrometer LCD outdoor

Range from 0°C to 70°C (32°F to 158°F) and 20% to 99% humidity Extra long cable (90cm) enables flexible positioning of the sensor Instructions: In/Out: Temperature at device (In) and at sensor (Out) Min/Max: Minimum and maximum temperatures measured Reset to zero: Press In/Out and Min/Max simultaneously for a short time Note: Do not place in the direct surroundings from heat and humidification sources Please remove batteries and dispose of them properly

RP Heat mat 5W 14x15cm @

Supports natural behavior, activity and metabolism. Optimized heating technology ensures even distribution of heat and low power consumption. Easy to install thanks to the self-adhesive layer. Suitable for terrarium and other animals. The heating mat is always placed on the outer part of the glass (base of terrarium or side wall). When placing on the outer glass of the terrarium base, use four rubber pads (the heating mat must not touch flammable materials). The heating mat heats the terrarium glass and thereby increases the temperature of the terrarium substrate. Warning: The heating mat must only be stuck from the outside of the terrarium. The heating mat must not touch any flammable materials. The heating area should be less than 1/3 of the terrarium area. Do not bend or cut. Do not immerse in liquid.

RP Heat mat 28W 53x28cm

Supports natural behavior, activity and metabolism. Optimized heating technology ensures even distribution of heat and low power consumption. Easy to install thanks to the self-adhesive layer. Suitable for terrarium and other animals. The heating mat is always placed on the outer part of the glass (base of terrarium or side wall). When placing on the outer glass of the terrarium base, use four rubber pads (the heating mat must not touch flammable materials). The heating mat heats the terrarium glass and thereby increases the temperature of the terrarium substrate. Warning: The heating mat must only be stuck from the outside of the terrarium. The heating mat must not touch any flammable materials. The heating area should be less than 1/3 of the terrarium area. Do not bend or cut. Do not immerse in liquid.

RP High pressure misting system @

High Pressure Adjustable Misting System Simulates the rainforest environment and humidity in a reptile terrarium By using the timing controller and the flow control knob on top of the main unit you can set the spraying time and mist output. On and Off control can be achieved any time through the remote control (not included) The unique shock absorbing design will create a relatively quiet operating environment

RP Membrane and key for fogger

The ceramic disk (membrane) is consumer goods, the life time is approximately 3000 hours. The membrane must to be changed once the mist effect begins to slow down. Its lifespan depends on a number of factors including water purity, operating time, water hardness etc. Exchanging the membrane: 1. Disconnect electric cable from the socket. 2. Remove sediment and limescale from Fogger. It is possible to use the water and vinegar solution (dip the Fogger for 30 minutes in the solution). After this dry the Fogger thoroughly. 3. Using the key (A) turn the round nut (B) anticlockwise. 4. Dismantle brass washer (C) and membrane (D). Leave the rubber washer (E) in the place. 5. Clean off chemical or mineral sediments from the round nut (B) and brass washer (C) with a soft cloth and fit on a new membrane (D). Black rings should point down. Inner space of the cavity has to be fully dry before installation of the new membrane. 6. Place the Fogger into a water container and keep flat and pour clean water into the container until the water level is 20mm to 40mm above the ceramic disk. 7. Connect the power cable of the Fogger to the transformer. Pluq the transformer into A/C power socket. The Fogger will start producing mist and water spray. At the same time, the LED lights begin to light.

RP Fogger Maxi accessory

Installation: 1. Remove all packaging. 2. Connect the connection part (3) to the water tank cover as shown in figure 1. 3. Connect the flexible hose (1) to the connecting part (3), as shown in figure 2. 4. Fit the suction cups on the glass (4) to a flexible hose (1) follow figure 3 and set the appropriate length of the flexible hose. 5. Attach the suction cups on the side or back of the terrarium as shown in figure 4 and place the outlet hole of the flexible hose towards the inside of the terrarium. Reduce bending of the extension tube as much as possible. Its damage may result in a non-functioning flow of generated fog from the fog machine. Part list: 1. Extension hose 2. Adapter – splitter 3. Connecting part 4. Suction cups

RP Breeding box 42x26x16cm

deal for transporting terrarium animals or feeding insects Stackable – permanent access to the feeding door from the side Ventilation holes from the side and top Large door for easy access from the top Highly transparent clear plastic for easy viewing Solid construction prevents animals from escaping

Sorting